Skip to content
FI – Suomeksi 050 322 5922

Heat pumps Espoo

An air-to-water heat pump in place of an oil boiler

We install air-to-water heat pumps in Espoo and the Helsinki region. Sizing is done for each property — it determines the result more than the choice of unit.

Two heat pump outdoor units on a concrete base

Why an air-to-water heat pump

An air-source heat pump is a supplementary heater. An air-to-water heat pump replaces the whole heating system: it heats both the house and the domestic hot water, and it is the only solution that really brings an oil or electricity bill down to a fraction. Compare heating alternatives.

Energy savings

60–80 %

Refrigerant work

Tukes TP103003

Warranty on work

1 year

Experience

Over 10 years

The right unit for the right house

Choosing the unit is not a matter of taste but of sizing. The model and output are chosen according to the heat demand of the house, the heat distribution and the hot water consumption, and according to what is already in place.

  • Models designed for northern conditions operate at temperatures as low as −25 to −28 °C
  • Heats the house and the domestic hot water
  • Hot water tank inside the indoor unit or separate, as the property requires
  • Refrigerant R32, or the new and highly environmentally friendly R290, i.e. propane
  • Sizing is done together with the technical support of the manufacturer’s importer

Sizing determines the result

The same pump can give an excellent or a disappointing result depending on how it is sized and how the heat distribution is done. The heat distribution — underfloor heating or radiators — is a separate choice, but it is sized together with the heat pump. We go through the property and make the calculations together with the importer’s technical support before anything is ordered. We often compare the heat pump to the heart and the radiators and heating pipes to the blood vessels: all of them need to be in good shape.

How the replacement works

  1. Survey and energy calculation

    We go through the property: the current heating method, the condition and sizing of the radiator system and the hot water demand. You get a calculation showing the estimated savings.

  2. Choosing and sizing the unit

    The model and output are chosen to suit the property. At this stage we also plan the renewal of the heat distribution, so that the heat pump can run at a low, energy-efficient water temperature.

  3. Installation

    The old system is removed and the new one installed. If needed, the heating pipes and the domestic water network are replaced on the same job.

  4. Commissioning

    The system is adjusted and we show you how to use it.

Air-to-water heat pumps — frequently asked questions

Is an air-to-water heat pump enough for a Finnish winter?

Yes. Models designed for northern conditions operate at temperatures as low as −25 to −28 °C, and the sizing makes sure the output is enough in the hardest frosts too.

Do the old radiators need to be replaced?

We recommend it. An air-to-water heat pump can produce hot water when needed, but the hotter the water it makes, the more electricity it uses. Old radiators sized for oil heating need hot water, whereas new energy-efficient radiators heat the rooms evenly at a lower temperature, so the heat pump runs at its best efficiency.

What do VILP and vilppi mean?

They are Finnish names for an air-to-water heat pump. VILP is short for vesi-ilmalämpöpumppu, and vilppi is the everyday word. You may also see ilma-vesilämpöpumppu or ilmavesilämpöpumppu in quotes and adverts — they all mean the same thing.

How much will I save?

Depending on the property and the work done, 60–80 %. We make an individual energy calculation for every property, so the estimate is based on your house, not on averages.

What warranty do the units have?

We give a one-year warranty on our work. The units are covered by the manufacturer’s warranty, the length of which depends on the unit — we always tell you before you order.

Can the heat pump also cool?

To a limited extent. Many models have a cooling function, but the effect depends on the heat distribution: water-based underfloor heating cools moderately when the system has dew point control, while radiators hardly cool at all. In Finnish conditions, the most cost-effective cooling is usually a separate air-source heat pump, which also adds extra power for the coldest frosts. We go through the options during the site visit.

Which refrigerants do the heat pumps use?

The options are R32 and, as a new alternative, the highly environmentally friendly R290, i.e. propane. R290 is a natural refrigerant whose global warming impact is a fraction of that of R32: the GWP of R32 is 675, that of R290 about 3.

Are you certified for refrigerant work?

Yes. We are registered in the Tukes qualification register for refrigerant work, registration number TP103003.

Which areas do you serve?

Espoo, Helsinki, Kirkkonummi, Kauniainen and Vantaa.

Request an energy calculation

Call and we will go through the property and make an energy calculation. The assessment does not commit you to anything.

+358 50 322 5922

Energy calculation request form